Repair and Service Garage Doors in Guelph, Kitchener | EasyFlip

Garage Door Service & Repair in Guelph, Kitchener area.

We are your One-Stop Solution for Garage Door and Garage Door Installation, Opener, Repairs, and Services.

Here are some helpful safety tips. This list is not intended to be a comprehensive list of every safety precaution. Always consult your manufacturer’s installation or instruction manual for safety information about your model.

Professional and timely Repair and Service of Garage Doors in the Guelph, Kitchener are.


✓ Broken Springs

✓ Broken Drums 

✓ Broken Cables 

✓ Broken Rollers 

✓ Rusted Bottom Brackets 

✓ Damaged Section 

✓ Broken Torsion Tube 

✓ Crooked Door 

✓ Need Strut


✓ Chain came off 

✓ Opener not working 

✓ Remote not working 

✓ Keypad not working 

✓ Opener wont open or close 

✓ Safety eyes problem 

✓ Broken sprocket Stripped gear

Broken or Loose Cables

 Frayed Garage Door Cables


It is through the cables that we find the high-pressure work of the spring getting transferred to lift the door.  

Cables bear the weight of the door when the door gets closed.  

The cable can break or come off of its spool.


The door opens or closes unevenly or shows visible signs of cables fraying or becoming loose, or disconnected. 



Call us right now and one of our experienced technicians will fix the problem. Get to the root of the cause to prevent the problem from happening again.

Broken Garage Door Springs



The most common issue that you will face with your garage is broken spring and this can lead the door to stop working. 


The torsion springs actually are the main component in the garage door opener and the hardest working part of the whole Garage door system.


The opener does only a fraction of the actual lifting that is necessary to move your garage door. 


Therefore, if the torsion spring stretches and breaks, the garage door opener will not be able to function and open the door. 


The symptoms of trouble with broken garage door springs include the door operating. 


There are 2 kinds of springs: 


1) Torsion Spring -These springs are placed just above the garage door and can expand or contract as the door raises or is lowered. It looks like firmly coiled springs. 


2) Extension Spring -These springs are positioned on the right and left sides of the garage doors and can stretch out and expand as the garage door lowers and contracts when opening. 



Do not try to operate the door as this is a safety hazard. Damaged springs can cause the garage door to crash down or injure someone. 



Get in touch with us who will fix the issue within the same day or within 24 hours.

Garage door rollers need to be reset or replaced



The garage door rollers are responsible for the smooth operation of the doors. 


These rollers are held in position with the help of brackets that are fixed to your garage and to the track. 


Those garage doors over a decade old have faced several environmental factors and build up from dust, lubricants, and oil. All these factors can start to take their toll and wear out those rollers. 


The quality of the rollers gets hampered and they can slip off the track from time to time.


You find your garage door making an excessive amount of noise when opening and closing and does not ride up and down smoothly. It might also seem to shake. 




Call our expert and well-trained technicians right now to fix the issue and act immediately for safety aspects and other reasons.

Safety Sensor Malfunction or Miss-alignment




Another common issue with a garage door is that it stops and then reverses if you want to close it. 


It also makes some clicking noise, accompanied by the opener light flashing. 


This clearly means that the safety sensors are out of alignment and the garage door will not close. 


As one side of the track acts as the receiving eye sensor and the other side sends the signal, if any one of these sensors are knocked out of alignment, the receiving end will not get the signal. 


This triggers the door to turn around.


The door goes back up when you hit the wall button in order to close the door. You have to press the button down until the door shuts.  




It is essential to keep the red lights on the sensors are on. 


Make manual adjustments if you see a flicker until lights are lit. 


If you still face the problem persists, it is essential to call us, the experts as there could be a bigger issue with the opener, for example, a circuit board problem.